Nordic Paws by DROPS Design

Knitted DROPS Christmas dog coat in ”Karisma” with traditional Norwegian pattern.

DROPS 102-42
Size: XS - S - M
The measures of the dog:
Chest width: approx 28/32 – 40/44 – 48/52 cm
Back length: approx 24 – 32 - 40 cm
Examples of sizes of dogs: XS = Chihuahua, S = Bichon Frise, M = Cocker Spaniel

Materials: DROPS Karisma from Garnstudio
50-100-150 g colour no. 18,red
50 - 50-100 g colour no. 01, off white

DROPS small circular needle size 3.5 mm (sock needle in smallest size) – or the size needed to obtain the correct knitting tension

DROPS double pointed needle and small circular needle size 3mm.


Knitting tension – See how to measure it and why here
Alternative Yarn – See how to change yarns here
Yarn Groups A to F – Use the same pattern and change the yarn here
Yarn usage using an alternative yarn – Use our yarn converter here


100% Wool
from 2.30 £ /50g
DROPS Karisma uni colour DROPS Karisma uni colour 2.30 £ /50g
Wool Warehouse Direct Ltd
DROPS Karisma mix DROPS Karisma mix 2.30 £ /50g
Wool Warehouse Direct Ltd
needles DROPS Needles & Hooks Order
You can get the yarn to make this pattern from 11.50£. Read more.

Pattern instructions

NOTE: This pattern is written in British English. All measurements in charts are in cm. For conversion from cm to inches - click here. There are different terms for crocheting in British and American English. If this pattern includes crochet, click for "crochet terms" here. For this pattern in American English, please click here.
Knitting Tension: . 22 sts x 30 rows in stocking sts = 10 x 10 cm

Pattern: See diagrams M.1 to M.5. The diagram are shown from the RS.

Rib: * K2, P2*, repeat from *-*

Knit the coat round from the top and down.
Cast on 52-72-92 sts with double pointed needle size 3 mm in Off white. Knit in Rib for 6-8-10 cm (= neck). Change to small circular needle size 3.5 mm (sock needle in the smallest size), knit 1 round in stocking sts at the same time inc. 8-12-16 sts evenly distributed = 60-84-108 sts.
Continue the pattern as follows:
Size XS: M.1, M.3 and M.5
Size S: M.1, M.2, M.3, M.4 and M.5
Size M: M.1, M.2 2 times, M.3, M.4 and M.5 2 times.
At the same time when the piece measures 10-14-18 cm split the piece for the forelegs as follows: Cast off 1 st, put 11-11-23 sts on a thread or a stitch holder (= underneath the stomach), cast off 1 st, and continue the pattern knitting back and forth on needle over the remaining 47-71-83 sts (= back piece).
When the piece measures a total of 16-22-28 cm (the opening measures approx. 6-8-10 cm) put sts on a thread or a stitch holder.
Put the sts from underneath the stomach back on needle and knit in pattern as for as long as the back piece.
Put all sts back on the same needle and cast on 1 new st each side in between the top and the bottom piece (back and underneath the stomach) = 60-84-108 sts. Finish the pattern, and continue with red until finish. When the piece measures 19-27-35 cm cast off 9-13-17 sts mid underneath the stomach. Then complete the work knitting back and forth on needle – at the same time cast off each side on every other row : 2 sts 1-2-3 times, 1 st 8-9-10 times, 2 sts 1-2-3 times and 3 sts 1 time = 21-31-41 sts left. The work measures approx. 27-37-47 cm.

Assembly: Put the remaining sts on a small circular needle size 3 mm and in addition pick up sts around the casting off edge so the total number of sts = approx. 84-108-140 sts. Knit Rib for 2½ -3-3 cm,cast off loosely.

Leg: Pick up approx 36-44-52 sts with double pointed needle size 3mm and red, around 1 of the openings of the leg. Knit in Rib for 3-4-6 cm, cast off loosely with K over K and P over P. Repeat for the other opening.


symbols = off white
symbols = red

Do you need help with this pattern?

Thank you for choosing a DROPS Design pattern. We take pride in providing patterns that are correct and easy to understand. All patterns are translated from Norwegian and you can always check the original pattern (DROPS 102-42) for measurements and calculations.

Are you having trouble following the pattern? See below for a list of resources to help you finish your project in no time - or why not, learn something new.

signature-image signature

Are you having trouble following the pattern? See below for a list of resources to help you finish your project in no time - or why not, learn something new.

Each of our patterns has specific tutorial videos to help you.

We have also step-by-step guides for different techniques which you'll find here.

1) Why is the knitting/crochet tension so important?

Knitting tension is what determines the final measurements of your work, and is usually measured per 10 x 10 cm. It is provided like so: number of stitches in width x number of rows in height - eg: 19 stitches x 26 rows = 10 x 10 cm.

The knitting tension is very individual; some people knit/crochet loosely while others work tightly. You adjust the knitting tension with the needle size, which is why the suggested needle size only serve as a guide! You need to adjust this (up or down) to ensure that YOUR knitting tension matches the knitting tension provided in the pattern. If you work with a different knitting tension than provided you will have a different yarn consumption, and your work will have different measurements than what the pattern suggests.

The knitting tension also determines which yarns can replace each other. As long as you achieve the same knitting tension you can replace one yarn with another.

See DROPS lesson: How to measure your tension/gauge

See DROPS video: How to make a gauge tension swatch

to top

2) What are the yarn groups?

All our yarns are categorised into yarn groups (from A to F) according to thickness and knitting tension – group A contains the thinnest yarns and group F the thickest. This makes it easier for you to find alternative yarns to our patterns, should you wish to switch yarn. All yarns within the same group have a similar knitting tension and can easily replace each other. However, different yarn qualities have different structures and properties which will give the finished work a unique look and feel.

Click here for an overview of the yarns in each yarn group

to top

3) Can I use a different yarn than what the pattern suggests?

The important thing when changing from one yarn to another is that the knitting/crochet tension remains the same. This is so that the measurements of the finished piece will be the same as on the sketch provided. It is easier to achieve the same knitting tension using yarns from the same yarn group. It is also possible to work with multiple strands of a thinner yarn to achieve the knitting tension of a thicker one. Please try our yarn converter. We recommend you to always work a test swatch.

Please NOTE: when changing yarn the garment might have a different look and feel to the garment in the photo, due to individual properties and qualities of each yarn.

See DROPS lesson: Can I use a different yarn than the one mentioned in the pattern?

to top

4) How do I use the yarn converter?

At the top of all our patterns you’ll find a link to our yarn converter, which is a helpful tool should you wish to use a different yarn than suggested. By filling in the yarn quality you wish to replace, the amount (in your size) and number of strands, the converter will present good alternative yarns with the same knitting tension. Additionally it will tell you how much you’ll require in the new qualities and whether you’ll need to work with multiple strands. Most skeins are 50g (some are 25g or 100g).

If the pattern is worked with multiple colours, every colour will have to be converted separately. Similarly, if the pattern is worked with several strands of different yarns (for example 1 strand Alpaca and 1 strand Kid-Silk) you will have to find alternatives for each, individually.

Click here to see our yarn converter

to top

5) Why do I get the wrong knitting tension with the suggested needle size?

The needle size provided in the pattern serves only as a guide, the important thing is to follow the knitting tension. And since knitting tension is very individual, you will have to adjust the needle size to ensure that YOUR tension is the same as in the pattern – maybe you’ll have to adjust 1, or even 2 needle sizes, up or down to achieve the correct tension. For this, we recommend that you work test swatches.

Should you work with a different knitting tension than the one provided, the measurements of the finished garment might deviate from the measurement sketch.

See DROPS lesson: How to measure your tension/gauge

See DROPS video: How to make a gauge tension swatch

to top

6) Why is the pattern worked top-down?

Working a garment top-down provides more flexibility and room for personal adjustment. For example it is easier to try the garment on while working, as well as making adjustments to length of yoke and shoulder caps.

The instructions are carefully explaining every step, in the correct order. Diagrams are adjusted to the knitting direction and are worked as usual.

to top

7) Why are the sleeves shorter in larger sizes?

The total width of the garment (from wrist-to-wrist) will be larger in the larger sizes, despite the actual sleeves being shorter. The larger sizes have longer sleeve caps and wider shoulders, so there will be a good fit in all sizes.

to top

8) What is a repeat?

Diagrams are often repeated on the round or in height. 1 repeat is the diagram the way it appears in the pattern. If it says to work 5 repeats of A.1 in the round, then you work A.1 a total of 5 times after/next to each other in the round. If it says to work 2 repeats of A.1 vertically/in height you work the entire diagram once, then begin again at the start and work the entire diagram one more time.

to top

9) How do I work according to a knitting diagram?

The diagram depicts all rows/rounds, and every stitch seen from the right side. It is read from bottom to top, from right to left. 1 square = 1 stitch.

When working back and forth, every other row is worked from the right side and every other row is worked from the wrong side. When working from the wrong side, the diagram will have to be worked reversed: from left to right, knit stitches are purled, purl stitches are knit etc.

When working in the round every round is worked from the right side and the diagram are worked from right to left on all rounds.

See DROPS lesson: How to read knitting diagrams

to top

10) How do I work according to a crochet diagram?

The diagram depicts all rows/rounds, and every stitch seen from the right side. It is worked from bottom to top, from right to left.

When working back and forth every other row is worked from the right side: from right to left and every other row is worked from the wrong side: from left to right.

When working in the round, every row in the diagram are worked from the right side, from right to left.

When working a circular diagram you start in the middle and work your way outwards, counter clockwise, row by row.

The rows usually start with a given number of chain stitches (equivalent to the height of the following stitch), this will either be depicted in the diagram or explained in the pattern.

See DROPS lesson: How to read crochet diagrams

to top

11) How do I work several diagrams simultaneously on the same row/round?

Instructions for working several diagrams after each other on the same row/round, will often be written like so: “work A.1, A.2, A.3 a total of 0-0-2-3-4 times". This means you work A.1 once, then A.2 is worked once, and A.3 is repeated (in width) the number of times provided for your size – in this case like so: S = 0 times, M = 0 times, L=2 times, XL= 3 times and XXL = 4 times.

The diagrams are worked as usual: begin with the first row in A.1, then work the first row in A.2 etc.

See DROPS lesson: How to read knitting diagrams

See DROPS lesson: How to read crochet diagrams

to top

12) Why does the piece start with more chain stitches than it’s worked with?

Chain stitches are slightly narrower than other stitches and to avoid working the cast-on edge too tight, we simply chain more stitches to begin with. The stitch count will be adjusted on the following row to fit the pattern and measurement sketch.

to top

13) Why increase before the rib edge when the piece is worked top-down?

The rib edge is more elastic and will contract slightly compared to, for example, stocking stitch. By increasing before the rib edge, you avoid a visible difference in width between the rib edge and the rest of the body.

to top

14) Why increase in the cast-off edge?

It’s very easy to cast off too tightly, and by making yarn overs while casting off (and simultaneously casting these off) you avoid a too tight cast off edge.

See DROPS video: How to bind off with yarn overs (yo)

to top

15) How do I increase/decrease on every 3rd and 4th row/round alternately?

To achieve an even increase (or decrease) you can increase on, for example: every 3rd and 4th row alternately, like so: work 2 rows and increase on the 3rd row, work 3 rows and increase on the 4th. Repeat this until the increase is complete.

See DROPS lesson: Increase or decrease 1 st on every 3rd and 4th row alternately

to top

16) Why is the pattern slightly different than what I see in the photo?

Pattern repeats can vary slightly in the different sizes, in order to get the correct proportions. If you’re not working the exact same size as the garment in the photo, yours might deviate slightly. This has been carefully developed and adjusted so that the complete impression of the garment is the same in all sizes.

Make sure to follow instructions and diagrams for your size!

to top

17) How can I work a jacket in the round instead of back and forth?

Should you prefer to work in the round instead of back and forth, you may of course adjust the pattern. You’ll need to add steeks mid-front (usually 5 stitches), and follow the instructions. When you would normally turn and work from the wrong side, simply work across the steek and continue in the round. At the end you’ll cut the piece open, pick up stitches to work bands, and cover the cut edges.

See DROPS video: How to knit steeks and cut open

to top

18) Can I work a jumper back and forth instead of in the round?

Should you prefer to work back and forth instead of in the round, you may of course adjust the pattern so you work the pieces separately and then assemble them at the end. Divide the stitches for the body in 2, add 1 edge stitch in each side (for sewing) and work the front and back pieces separately.

See DROPS lesson: Can I adapt a pattern for circular needles into straight needles?

to top

19) Why do you show discontinued yarns in the patterns?

Since different yarns have different qualities and textures we have chosen to keep the original yarn in our patterns. However, you can easily find options among our available qualities by using our yarn converter, or simply pick a yarn from the same yarn group.

It is possible that some retailers still have discontinued yarns in stock, or that someone has a few skeins at home that they would like to find patterns for.

The yarn converter will provide both alternative yarn as well as required amount in the new quality.

to top

20) How do I make a women’s size garment into a men’s size one?

If you have found a pattern you like which is available in women’s size it’s not very difficult to convert it to men’s size. The biggest difference will be the length of sleeves and body. Start working on the women size that you think would fit across the chest. The additional length will be worked right before you cast off for the armhole/sleeve cap. If the pattern is worked top-down you can add the length right after the armhole or before the first decrease on sleeve.

Regarding additional yarn amount, this will depend on how much length you add, but it is better with a skein too many than too few.

to top

21) How do I prevent a hairy garment from shedding?

All yarns will have excess fibres (from production) that might come off as lint or shedding. Brushed yarns (ie hairier yarns) have more of these loose, excess fibres, causing more shedding.

Shedding also depends on what is worn under or over the garment, and whether this pulls at the yarn fibres. It’s therefore not possible to guarantee that there will be no shedding

Below are some tips on how to get the best result when working with hairier yarns:

1. When the garment is finished (before you wash it) shake it vigorously so the looser hairs come off. NOTE: do NOT use a lint roller, brush or any method that pulls at the yarn.

2. Place the garment in a plastic bag and put it in your freezer - the temperature will cause the fibres to become less attached to each other, and excess fibres will come off easier.

3. Leave in the freezer for a few hours before taking it out and shaking it again.

4. Wash the garment according to the instructions on the yarn label.

to top

22) Where on the garment is the length measured?

The measurement sketch/schematic drawing provides information regarding the full length of the garment. If it’s a jumper or a jacket the length is measured from the highest point on the shoulder closest to the neckline, and straight down to the bottom of the garment. It is NOT measured from the tip of shoulder. Similarly, the length of yoke is measured from the highest point on the shoulder and down to where yoke is split into body and sleeves.

On a jacket measures are never taken along bands, unless specifically stated. Always measure inside band stitches when measuring the length.

See DROPS lesson: How to read a schematic drawing

to top

23) How do I know how many balls of yarn I need?

The required amount of yarn is provided in grams, eg: 450 g. To calculate how many balls you’ll need you first need to know how many grams are in 1 ball (25g, 50g or 100g). This information is available if you click on the individual yarn quality on our pages. Divide the amount required with the amount of each ball. For example, if each ball is 50g (the most common amount), the calculation will be as follows: 450 / 50 = 9 balls.

to top

Have you purchased DROPS yarn to make this pattern? Then you are entitled to receive help from the store where you bought the yarn. Find a list of DROPS stores here!
Still can't find the answer you need? Then scroll down and leave your question so one of our experts can try to help you. This will be done normally within 5 to 10 working days. In the meantime, you can read the questions and answers that others have left to this pattern or join the DROPS Workshop on Facebook to get help from fellow knitters/crocheters!

Comments / Questions (81)

country flag Irina Peshkina wrote:

I knitted this jamper for me sister's dog Happy. Amazing pattern!

04.12.2023 - 10:49

country flag LaetiKv wrote:

Je pense qu'il faudrait modifier le nombre de mailles à mettre en attente pour l'abdomen de la taille S car le nombre de mailles à mettre en attente est le même pour les tailles XS et S. Il vaudrait mieux faire 11-17-23 m.

04.08.2023 - 09:25

country flag Giada wrote:

Salve, quando il lavoro misura 10 cm dovrei dividere le maglie per le zampe anteriori ma come faccio? Perché avendo 60 maglie se faccio i 2 intrecci e metto da parte le maglie per la pancia mi risulterebbero solo 45 maglie e non 47 e così non potrei seguire il motivo. Grazie

07.04.2022 - 23:27

DROPS Design answered:

Buonasera Giada, con 60 maglie a 10 cm deve intrecciare 1 maglia e mettere in sospeso 11 maglie (= 48 maglie rimaste), intrecciare 1 maglia e lavorare sulle altre 47 maglie. Buon lavoro!

08.04.2022 - 22:49

country flag Christine Lindop wrote:

I'm not sure what the measurement 'burst' refers to. I'm an experienced knitter, but not for dogs!

25.05.2021 - 12:56

DROPS Design answered:

Dear Mrs Lindop, oops typo... the "burst" measurements should be bust = chest measurements. Happy knitting!

25.05.2021 - 14:17

country flag Adinda wrote:

Beste, ik zou graag truitjes breien voor mn franse bulldogskes .. maar weet niet goed,hoe eraan te beginne.. heb jij soms een voorbeeld en info ofzo ervan ? Of patronen waar ik ong zoiets kan breien ajb ? Of waar ik t kan afhalen of bekijken ? K ben al dagen aan t zoeken,tt op hede nog niks gevonden helaas !! En mn handjes kribbelen vr eraan te beginne 😃 Mvg.Adinda

31.01.2021 - 13:36

DROPS Design answered:

Dag Adinda,

Op onze site staan een aantal hondentruien die je kunt gebruiken. Bovenaan bij de maten en materialen staat de borstwijdte en ruglengte meestal aangegeven. Misschien kun je de afmetingen aanpassen door meer of minder steken op te zetten. Dit kun je uit rekenen aan de hand van de stekenverhouding.

01.02.2021 - 08:35

country flag Suzie Rénald wrote:

Bonjour, Pour les diminutions de la fin, il est indiqué de diminuer 1 fois 3 mailles . Peut-on diminuer 3 mailles d’un seul coup et le cas échéant, comment faire ? Je sais comment réaliser des diminutions simples et doubles mais triples , je ne sais pas faire :( merci à l’avance.

12.12.2020 - 22:52

DROPS Design answered:

Bonjour Mme Rénald, à la fun du manteau, après avoir rabattu les mailles centrales, vous continuez en allers et retours en rabattant les mailles de chaque côté: d'abord 2 mailles, puis 1 maille, puis 2 mailles et enfin 3 mailles, ces mailles doivent être rabattues au début de chaque rang, de chaque côté et non diminuées. Bon tricot!

14.12.2020 - 08:36

country flag Suzie Rénald wrote:

Bonjour, je voudrais savoir si les instructions de ce modèle existent en français ? Merci

02.12.2020 - 00:18

DROPS Design answered:

Bonjour Mme Rénald, tous nos modèles sont disponibles en français, cliquez sur le menu déroulant sous la photo pour changer la langue. Bon tricot!

02.12.2020 - 07:57

country flag Johanne Brøsted wrote:

Jeg er i tvivl om delingen til "ærmer" samt forside/bagside der skal foregå (i mit tilfælde) efter14 cm. Er det 14 cm fra starten af arbejdet = 4 cm efter påbegyndelsen af kroppen, eller er det 14 cm fra begyndelsen af kroppen? Det virker som om 4 cm er meget lidt for et skulderparti.

06.11.2020 - 19:28

DROPS Design answered:

Hej Johanne, ja det er fra opslåningskanten du måler :)

10.11.2020 - 09:39

country flag Clara wrote:

Just one question. Is there any difference between this pattern and the one with the Chihuahua in the picture? Link: /pattern.php?id=5617&cid=17 i found no difference at a glance. I just want to make sure I\'m not doing the same one twice.

10.02.2020 - 04:20

DROPS Design answered:

Dear Clara, you are right, it's almost the same pattern, just shown in different sizes. Happy knitting!

10.02.2020 - 10:21

country flag Catherine wrote:

Has anyone made this pattern for a King Charles Spaniel? If so, which size did you make?

27.12.2019 - 16:42

DROPS Design answered:

Dear Catherine, you will find all measurements under header, measure the dog and check the best matching size - should you need any further assistance choosing the size, you are welcome to contact your DROPS store, even per mail or telephone. Happy knitting!

02.01.2020 - 11:38

Post a comment to pattern DROPS 102-42

We would love to hear what you have to say about this pattern!

If you want to leave a question, please make sure you select the correct category in the form below, to speed up the answering process. Required fields are marked *.