DROPS Super Sale - SAVE 30% on 6 yarns all June!

Lifeline in knitting

Video thumbnail for Lifeline in knitting
When you work lace and other patterns adding a so called lifeline can save you a lot of trouble. After finishing a full repeat of pattern, sew a strand of yarn, or like we do a strand of dental floss through all sts on needle. If you then a few rows later mess up, you can easily and safe unravel back to the sts on the lifeline, put sts back on needle and give it a new shot. After next repeat, add one more lifeline.
Using dental floss is great since you will not have any trouble pulling it out of the work later, and also being thin but never will break.
Change language:

Video #210, listed in: Other techniques, Extra Tips

Our videos do not have sound. We are a worldwide company and our videos are watched by people speaking endless of different languages and many do not understand English. So since there is not a given language for us to use, we instead have written instructions to accompany the video, and then there is no sound to disturb while watching.

You can adjust the speed of this video by clicking on the icon, on the play bar.

Country flag Jutta wrote:

Sehr guter Tipp. Genial.

28.01.2012 - 12:03

Lakshmi wrote:

Yes the dental floss idea is good specially for lace and also for cables too.

09.01.2012 - 14:00

Audrey wrote:

Très bonne idée! Ça évite beaucoup de tracas, merci beaucoup!

08.01.2012 - 23:54

Country flag Gloria Hieser wrote:

Awesome!!! Great tip and very helpful. Now I have to make sure I buy unflavered dental tape for my knitting! Although minty fresh knitting may not be a bad idea :)

01.12.2011 - 23:54

Country flag Debra wrote:

I like it!

20.11.2011 - 22:38

Silvia wrote:

Great tip!!

18.11.2011 - 07:27

Leave a comment or question to this video

Your email address will not be published. Required fields are marked *.

You might also like

Video thumbnail for How to work with 2 circular needles with different needle sizes
9:10
How to work with 2 circular needles with different needle sizes

In this DROPS video we show you how to work rib in a stockinette stitch piece. To allow the rib to tighten, work the rib with a smaller needle size than the rest of the piece. Use both ends of the needle when working.
Video thumbnail for How to crochet a cord with 2 strands / 2 colors
2:02
How to crochet a cord with 2 strands / 2 colors

In this DROPS video we show how to crochet a cord with 2 strands / 2 colors. Place the strands together, but use your left index finger to hold the threads apart (let one strand (pink) lie at the top above the finger and let the other strand (light blue) lie at the bottom under the index finger) and make sure that the strands that are to be crocheted with are in the same order along the way. Work like this: * Take the hook over and around the light blue strand (2 loops on the hook), take the hook under and around the pink strand and pull the pink strand through both loops on the hook *, work from *-* to desired length. Cut the strands leaving 10 cm = 4" (used to fasten the cord), thread the pink strand through the last loop on the hook. We use the yarn DROPS Snow in the video. You’ll find a pattern using this technique by clicking on the picture below.
Video thumbnail for How to make a decoration knot
1:27
How to make a decoration knot

In this DROPS video we show how to make a knot to be attached as a decoration to a Santa that is worked on a sweater. The same technique is also used to make a star at the top of a Christmas tree sweater. KNOT: Make a knot at the top of every Santa hat/ Christmas tree. Tie the knot around a stitch. Cut 2 lengths of color off white. approx. 10 cm = 4". Place strands together, use a needle and pull strands through the top off white stitch so that both yarn ends are on the right side of piece, on each side of stitch. Tie a knot, then tie another knot but in the opposite direction. Cut the yarn ends approx. ½ cm = 1/8" (Santa) / 1 cm = 2/8" (Christmas tree) long. These sweaters are worked in DROPS Air but in the video, we work with a thicker yarn; DROPS Snow., You must read the pattern to be able to follow this video properly. You’ll find a pattern by clicking on one off the picture below.
Video thumbnail for How to sew / embroider twisted chain stitch
2:25
How to sew / embroider twisted chain stitch

In this DROPS video we show how to sew / embroider twisted chain stitch. Insert the needle from the wrong side and through to the right side where you would like the chain stitch to begin. * Thread the needle down through the hole the strand came up through, then to the right side again approx. 2 cm = 3/4" further on – allow the strand to lie in a loop around the tip of the needle. Pick up the loop and twist it 2-3 times before laying it down again under the tip of the needle. Pull the strand through carefully, so the stitch is neat. If you want more stitches in height, repeat from the *. Finish by thread the needle through the piece approx. 0.5 stitches in front of the loop and pull it through to the wrong side. We use the yarn DROPS Snow in the video. You must read a pattern using this technique to be able to follow this video properly. You’ll find a pattern by clicking on one of the pictures below.
Video thumbnail for How to sew / embroider flat stitch
1:28
How to sew / embroider flat stitch

In this DROPS video we show how to sew / embroider flat stitch. Insert the needle from the wrong side to the right side, where you wish the stitch to start. Skip 0.5 - 1 cm = 1/8" - 3/8" and thread the needle down and up again to where you want the next flat stitch to start, pull the strand through. Skip 0.5 - 1 cm = 1/8" - 3/8" and thread the needle down and up again to where you want the next flat stitch to start, pull the strand through. Continue like this until you have enough stitches. We use the yarn DROPS Snow in the video. You must read a pattern using this technique to be able to follow this video properly. You’ll find a pattern by clicking on one of the pictures below.
Video thumbnail for How to sew / embroider back-stitch knot
1:47
How to sew / embroider back-stitch knot

In this DROPS video we show how to sew / embroider back stitch knots. Insert the needle from the wrong side and through to the right side where you wish the knot to be. Thread the needle back to the wrong side 0.5 – 1.5 stitches from where it originally came up. Sew up and down through the same holes as many times as is necessary to give the knot size you wish. We use the yarn DROPS Snow in the video. You must read a pattern using this technique to be able to follow this video properly. You’ll find a pattern by clicking on one of the pictures below.