DROPS Nepal
DROPS Nepal
65% Wool, 35% Alpaca
from 2.40 £ /50g
Get the yarn to make this pattern from 4.80£.

The yarn cost is calculated from the pattern’s smallest size and the yarn’s cheapest product type. Looking for an even better price? You might find it on the DROPS Deals!

DROPS Super Sale
DROPS 150-40
DROPS design: Pattern no ne-128
Yarn group C
-----------------------------------------------------------
HAT:
Size: S/M - L/XL
Head circumference: approx. 53/55 - 56/58 cm
Materials:
DROPS NEPAL from Garnstudio
100-100 g colour no 0501, grey

DROPS STRAIGHT NEEDLES SIZE 4.5 mm - or size needed to get 17 sts x 30 rows moss st = 10 x 10 cm.

-------------------------------------------------------

Alternative Yarn – See how to change yarns here
Yarn Groups A to F – Use the same pattern and change the yarn here
Yarn usage using an alternative yarn – Use our yarn converter here

-------------------------------------------------------

DROPS Nepal
DROPS Nepal
65% Wool, 35% Alpaca
from 2.40 £ /50g
Get the yarn to make this pattern from 4.80£.

The yarn cost is calculated from the pattern’s smallest size and the yarn’s cheapest product type. Looking for an even better price? You might find it on the DROPS Deals!

DROPS Super Sale

SAVE 30% on 6 cotton favourites!
Valid until 12.04.2024

Pattern instructions

NOTE: This pattern is written in British English. All measurements in charts are in cm. For conversion from cm to inches - click here. There are different terms for crocheting in British and American English. If this pattern includes crochet, click for "crochet terms" here. For this pattern in American English, please click here.
DOUBLE MOSS ST (in hight):
Row 1 (RS): * K 1, P 1 *, repeat from *-*.
Row 2 (WS): K over K and P over P.
Row 3: P over K and K over P.
Row 4: As 2nd row.
Repeat row 1 to 4.

GARTER ST (back and forth on needle):
K all rows. 1 ridge = 2 rows K.
----------------------------------------------------------

HAT:
Worked back and forth on needle. Cast on 80-88 sts with Nepal on needle size 4.5 mm. K 1 row, then work DOUBLE MOSS ST - see explanation above - over all sts.
When piece measures 20-21 cm (adjust so that last row is from RS), work in GARTER ST - see explanation above - until finished measurements AT THE SAME TIME dec every 4th row as follows:
Row 4: Dec 16-18 sts evenly (= approx. every 5th st) = 64-70 sts on needle.
Row 8: Dec 13-14 sts (= approx. 5th st) = 51-56 sts.
Row 12: Dec 10-11 sts (= approx. 5th st) = 41-45 sts.
Row 16: Dec 9-9 sts (= approx. 5th st) = 32-36 sts.
Row 20: K all sts tog 2 by 2 = 16-18 sts.
Row 24: K all sts tog 2 by 2 = 8-9 sts.
Cut the yarn and pull it through the remaining sts. Sew hat tog mid back, edge to edge to avoid a chunky seam. Hat measures approx. 26-27 cm. Fasten yarn tightly.
Do you have a question? See a list of frequently asked questions (FAQ)

Knitting tension is what determines the final measurements of your work, and is usually measured per 10 x 10 cm. It is provided like so: number of stitches in width x number of rows in height - eg: 19 stitches x 26 rows = 10 x 10 cm.

The knitting tension is very individual; some people knit/crochet loosely while others work tightly. You adjust the knitting tension with the needle size, which is why the suggested needle size is only meant as a guide! You need to adjust this (up or down) to ensure that YOUR knitting tension matches the knitting tension provided in the pattern. If you work with a different knitting tension than provided you will have a different yarn consumption, and your work will have different measurements than what the pattern suggests.

The knitting tension also determines which yarns can replace each other. As long as you achieve the same knitting tension you can replace one yarn with another.

See DROPS lesson: How to measure your tension/gauge

See DROPS video: How to make a gauge tension swatch

The required amount of yarn is provided in grams, eg: 450 g. To calculate how many balls you’ll need you first need to know how many grams are in 1 ball (25g, 50g or 100g). This information is available if you click on the individual yarn quality on our pages. Divide the amount required with the amount of each ball. For example, if each ball is 50g (the most common amount), the calculation will be as follows: 450 / 50 = 9 balls.

The important thing when changing from one yarn to another is that the knitting/crochet tension remains the same. This is so that the measurements of the finished piece will be the same as on the sketch provided. It is easier to achieve the same knitting tension using yarns from the same yarn group. It is also possible to work with multiple strands of a thinner yarn to achieve the knitting tension of a thicker one. Please try our yarn converter. We recommend you to always work a test swatch.

Please NOTE: when changing yarn the garment might have a different look and feel to the garment in the photo, due to individual properties and qualities of each yarn.

See DROPS lesson: Can I use a different yarn than the one mentioned in the pattern?

All our yarns are categorised into yarn groups (from A to F) according to thickness and knitting tension – group A contains the thinnest yarns and group F the thickest. This makes it easier for you to find alternative yarns to our patterns, should you wish to switch yarn. All yarns within the same group have a similar knitting tension and can easily replace each other. However, different yarn qualities have different structures and properties which will give the finished work a unique look and feel.

Click here for an overview of the yarns in each yarn group

At the top of all our patterns you’ll find a link to our yarn calculator, which is a helpful tool should you wish to use a different yarn than suggested. By filling in the yarn quality you wish to replace, the amount (in your size) and number of strands, the calculator will present good alternative yarns with the same knitting tension. Additionally it will tell you how much you’ll require in the new qualities and whether you’ll need to work with multiple strands. Most skeins are 50g (some are 25g or 100g).

If the pattern is worked with multiple colours, every colour will have to be calculated separately. Similarly, if the pattern is worked with several strands of different yarns (for example 1 strand Alpaca and 1 strand Kid-Silk) you will have to find alternatives for each, individually.

Click here to see our yarn calculator

Since different yarns have different qualities and textures we have chosen to keep the original yarn in our patterns. However, you can easily find options among our available qualities by using our yarn calculator, or simply pick a yarn from the same yarn group.

It is possible that some retailers still have discontinued yarns in stock, or that someone has a few skeins at home that they would like to find patterns for.

The yarn calculator will provide both alternative yarn as well as required amount in the new quality.

If you think it's hard to decide what size to make, it can be a good idea to measure a garment you own already and like the size of. Then you can pick the size by comparing those measures with the ones available in the pattern's size chart.

You'll find the size chart at the bottom of the pattern.

See DROPS lesson: How to read size chart

The needle size provided in the pattern serves only as a guide, the important thing is to follow the knitting tension. And since knitting tension is very individual, you will have to adjust the needle size to ensure that YOUR tension is the same as in the pattern – maybe you’ll have to adjust 1, or even 2 needle sizes, up or down to achieve the correct tension. For this, we recommend that you work test swatches.

Should you work with a different knitting tension than the one provided, the measurements of the finished garment might deviate from the measurement sketch.

See DROPS lesson: How to measure your tension/gauge

See DROPS video: How to make a tension/gauge swatch

Working a garment top-down provides more flexibility and room for personal adjustment. For example it is easier to try the garment on while working, as well as making adjustments to length of yoke and shoulder caps.

The instructions are carefully explaining every step, in the correct order. Diagrams are adjusted to the knitting direction and are worked as usual.

The diagram depicts all rows/rounds, and every stitch seen from the right side. It is read from bottom to top, from right to left. 1 square = 1 stitch.

When working back and forth, every other row is worked from the right side and every other row is worked from the wrong side. When working from the wrong side, the diagram will have to be worked reversed: from left to right, knit stitches are purled, purl stitches are knit etc.

When working in the round every round is worked from the right side and the diagram are worked from right to left on all rounds.

See DROPS lesson: How to read knitting diagrams

The diagram depicts all rows/rounds, and every stitch seen from the right side. It is worked from bottom to top, from right to left.

When working back and forth every other row is worked from the right side: from right to left and every other row is worked from the wrong side: from left to right.

When working in the round, every row in the diagram are worked from the right side, from right to left.

When working a circular diagram you start in the middle and work your way outwards, counter clockwise, row by row.

The rows usually start with a given number of chain stitches (equivalent to the height of the following stitch), this will either be depicted in the diagram or explained in the pattern.

See DROPS lesson: How to read crochet diagrams

Instructions for working several diagrams after each other on the same row/round, will often be written like so: “work A.1, A.2, A.3 a total of 0-0-2-3-4 times". This means you work A.1 once, then A.2 is worked once, and A.3 is repeated (in width) the number of times provided for your size – in this case like so: S = 0 times, M = 0 times, L=2 times, XL= 3 times and XXL = 4 times.

The diagrams are worked as usual: begin with the first row in A.1, then work the first row in A.2 etc.

See DROPS lesson: How to read knitting diagrams

See DROPS lesson: How to read crochet diagrams

The total width of the garment (from wrist-to-wrist) will be larger in the larger sizes, despite the actual sleeves being shorter. The larger sizes have longer sleeve caps and wider shoulders, so there will be a good fit in all sizes.

The measurement sketch/schematic drawing provides information regarding the full length of the garment. If it’s a jumper or a jacket the length is measured from the highest point on the shoulder closest to the neckline, and straight down to the bottom of the garment. It is NOT measured from the tip of shoulder. Similarly, the length of yoke is measured from the highest point on the shoulder and down to where yoke is split into body and sleeves.

On a jacket measures are never taken along bands, unless specifically stated. Always measure inside band stitches when measuring the length.

See DROPS lesson: How to read a schematic drawing

Diagrams are often repeated on the round or in height. 1 repeat is the diagram the way it appears in the pattern. If it says to work 5 repeats of A.1 in the round, then you work A.1 a total of 5 times after/next to each other in the round. If it says to work 2 repeats of A.1 vertically/in height you work the entire diagram once, then begin again at the start and work the entire diagram one more time.

Chain stitches are slightly narrower than other stitches and to avoid working the cast-on edge too tight, we simply chain more stitches to begin with. The stitch count will be adjusted on the following row to fit the pattern and measurement sketch.

The rib edge is more elastic and will contract slightly compared to, for example, stocking stitch. By increasing before the rib edge, you avoid a visible difference in width between the rib edge and the rest of the body.

It’s very easy to cast off too tightly, and by making yarn overs while casting off (and simultaneously casting these off) you avoid a too tight cast off edge.

See DROPS video: How to bind off with yarn overs (yo)

To achieve an even increase (or decrease) you can increase on, for example: every 3rd and 4th row alternately, like so: work 2 rows and increase on the 3rd row, work 3 rows and increase on the 4th. Repeat this until the increase is complete.

See DROPS lesson: Increase or decrease 1 st on every 3rd and 4th row alternately

Should you prefer to work in the round instead of back and forth, you may of course adjust the pattern. You’ll need to add steeks mid-front (usually 5 stitches), and follow the instructions. When you would normally turn and work from the wrong side, simply work across the steek and continue in the round. At the end you’ll cut the piece open, pick up stitches to work bands, and cover the cut edges.

See DROPS video: How to knit steeks and cut open

Should you prefer to work back and forth instead of in the round, you may of course adjust the pattern so you work the pieces separately and then assemble them at the end. Divide the stitches for the body in 2, add 1 edge stitch in each side (for sewing) and work the front and back pieces separately.

See DROPS lesson: Can I adapt a pattern for circular needles into straight needles?

Pattern repeats can vary slightly in the different sizes, in order to get the correct proportions. If you’re not working the exact same size as the garment in the photo, yours might deviate slightly. This has been carefully developed and adjusted so that the complete impression of the garment is the same in all sizes.

Make sure to follow instructions and diagrams for your size!

If you have found a pattern you like which is available in women’s size it’s not very difficult to convert it to men’s size. The biggest difference will be the length of sleeves and body. Start working on the women size that you think would fit across the chest. The additional length will be worked right before you cast off for the armhole/sleeve cap. If the pattern is worked top-down you can add the length right after the armhole or before the first decrease on sleeve.

Regarding additional yarn amount, this will depend on how much length you add, but it is better with a skein too many than too few.

All yarns will have excess fibres (from production) that might come off as lint or shedding. Brushed yarns (ie hairier yarns) have more of these loose, excess fibres, causing more shedding.

Shedding also depends on what is worn under or over the garment, and whether this pulls at the yarn fibres. It’s therefore not possible to guarantee that there will be no shedding

Below are some tips on how to get the best result when working with hairier yarns:

1. When the garment is finished (before you wash it) shake it vigorously so the looser hairs come off. NOTE: do NOT use a lint roller, brush or any method that pulls at the yarn.

2. Place the garment in a plastic bag and put it in your freezer - the temperature will cause the fibres to become less attached to each other, and excess fibres will come off easier.

3. Leave in the freezer for a few hours before taking it out and shaking it again.

4. Wash the garment according to the instructions on the yarn label.

Pilling is a natural process that happens to even the most exclusive of fibers. It's a natural sign of wear and tear that is hard to avoid, and that is most visible in high friction areas of your garment like a sweater's arms and cuffs.

You can make your garment look as new by removing the pilling, using a fabric comb or a pill/lint remover.

Still can't find the answer you need? Then scroll down and leave your question so one of our experts can try to help you. This will be done normally within 5 to 10 working days.
In the meantime, you can read the questions and answers that others have left to this pattern or join the DROPS Workshop on Facebook to get help from fellow knitters/crocheters!

You might also like...

Post a comment to pattern DROPS 150-40

We would love to hear what you have to say about this pattern!

If you want to leave a question, please make sure you select the correct category in the form below, to speed up the answering process. Required fields are marked *.

Comments / Questions (115)

country flag Anka wrote:

Hallo, ich habe ein anderes Garn benutzt und die Mütze mit 118 Maschen bis vor die Abnahmen gestrickt. Jetzt frag ich mich gerade wie ich die Abnahmen am besten gestalte? Nehme ich da z.b. eher in jeder 2. Reihe jede 5. Masche ab oder lieber weiterhin in jeder 4. Reihe dann aber z.b. jeder 2. oder 3. Masche? Vielen Dank!

30.11.2016 - 14:13

DROPS Design answered:

Liebe Anka, Sie können sich von einem ähnlichen Modell mit Ihrer Maschenprobe mal inspieren. Viel Spaß beim stricken!

30.11.2016 - 16:16

country flag Worldbridger wrote:

Hoi, bij het bepalen van de maat: meet je zoals je de muts op de foto ziet: dus vanaf je nek, over oren tot je voorhoofd (diagonaal) . Of: vanaf het midden van de achterkant van je hoofd rondom naar de voorkant ( horizontaal) ?

28.11.2016 - 20:09

DROPS Design answered:

Hoi Worldbridger. Je meet de omtrek van je hoofd - dus "horizontaal"

29.11.2016 - 11:28

country flag Marlink wrote:

Si può lavorare con i ferri circolari e come? Grazie

23.10.2016 - 00:41

DROPS Design answered:

Buongiorno Marlink. Può lavorare con i ferri circolari unendo in tondo dopo aver avviato le m e seguendo le stesse spiegazioni. Cambia solo la maglia a legaccio che lavorerà: un giro a dir e uno a rov. Buon lavoro!

23.10.2016 - 08:25

Marta wrote:

Hi, I started on the hat and then I watched the video about seed stitch. Is it necessary in that hat to slip first stitch on the needle and then start the seed stitch? Or should I start with a seed stitch from the first stitch? Thanks

20.10.2016 - 16:48

DROPS Design answered:

Dear Marta, the hat is here worked back and forth, so that you may like to have 1 edge st on each side for seam allowance. Happy knitting!

21.10.2016 - 08:46

country flag Jardé wrote:

Je viens de m'apercevoir que toute la fin du bonnet :après 22 cm de hauteur totale doit se faire au point mousse. Donc je pense que ce n'est pas la peine que je supprime des rangs car je pense pas avoir de problème d'échantillon avec du point mousse. Savez-vous quelles sont les dimensions pour un échantillon de point mousse dans une épaisseur de fil c ? Bien merci.

06.07.2016 - 14:20

DROPS Design answered:

Bonjour Mme Jardé, vous pouvez ajuster les diminutions en fonction de votre tension et de la taille choisie: 6-7 cm au point mousse après le point de blé et avec les diminutions. Tricotez un échantillon au point mousse pour recalculer le nbe de rangs dont vous aurez besoin. Bon tricot!

06.07.2016 - 15:46

country flag Jardé wrote:

Merci pour votre réponse. Cependant n'est-ce pas le contraire ? Si j'obtiens des mailles plus grosses sur mon échantillon (donc moins de mailles dans 10cm) je dois supprimer des rangs entre deux augmentations ... Car sinon le bonnet sera trop long ... ?

06.07.2016 - 14:09

DROPS Design answered:

Bonjour Mme Jardé, si la largeur est bonne, c'est la hauteur que vous devrez ajuster, il faut 30 rangs au point de blé = 10 cm, s'il vous faut plus de 30 rangs pour 10cm, il vous faudra tricoter quelques rangs en moins, si vous avez moins de 30 rangs pour 10 cm, il vous faudra tricoter quelques rangs en moins - pardon pour la confusion.

06.07.2016 - 15:43

country flag Jardé wrote:

Bonjour. Je suis désespérée car l'échantillon n'est toujours pas bon. Quand je prends des aiguilles plus petites le nombre de rangs augmentent légèrement ainsi que le nombre de mailles :-( . Je tiens à préciser que j'utilise le fil drops Paris. Pensez-vous que je doive abandonner le modèle ? Merci

06.07.2016 - 12:46

DROPS Design answered:

Bonjour Mme Jardé, vous pouvez réaliser le bonnet avec les aiguilles qui vous donnent la bonne tension en largeur et ajuster les diminutions du bonnet en fonction de votre nbe de rangs en hauteur (si vous en avez moins, tricotez des rangs supplémentaires entre chaque rang de diminution, si vous en avez plus, tricotez des rangs en moins entre les rangs de diminutions). Bon tricot!

06.07.2016 - 13:33

country flag Jardé wrote:

Bonjour, Je ne comprends pas comment l'échantillon au point de blé peut contenir 30 rangs dans 10cm. J'en ai tricoté un en 4,5 et l'autre en 5, le nombre de mailles est pratiquement bon mais le nombre de rangs est seulement de 24.

05.07.2016 - 02:21

DROPS Design answered:

Bonjour Mme Jardé, le point de blé et ses m env vont contracter légèrement l'ouvrage en hauteur, on aura donc une tension différente de celle du jersey. Vous pouvez essayer différentes techniques pour les m end/m env pour conserver un peu de souplesse - voir onglet vidéos. Bon tricot!

05.07.2016 - 08:59

country flag Jardé wrote:

Bonjour, Je remarque qu'il est demandé de tricoter en 4,5 alors que les indications sur les pelotes Nepal demandent une largeur de 5mm. Cordialement

12.06.2016 - 23:48

DROPS Design answered:

Bonjour Mme Jardé, pour le bonnet, vous devez avoir un échantillon de 17 m x 30 rangs au point de blé, avec des aiguilles 4,5 - ajustez la taille des aiguilles si besoin pour bien avoir l'échantillon. Bon tricot!

13.06.2016 - 09:48

country flag Jardé wrote:

Bonjour, Doit-on faire une mailles lisière "spéciale" pour un assemblage plus facile par la suite ? merci de votre réponse

12.06.2016 - 23:40

DROPS Design answered:

Bonjour Mme Jardé, tricotez vos mailles lisières soit au point de blé, soit comme vous en avez l'habitude en fonction de la façon dont vous réalisez la couture. Bon tricot!

13.06.2016 - 09:33